Top Janatics Accessories,Festo Accessories,Festo Solenoid Valve Products in Vadodara at best prices | ADVANCE INDUSTRIES -FESTO-JANATICS-KITZ-BELIMO-SMC

FESTO Pneumatic Tubing

O.D. pneumatic tubing is the current standard in pneumatics. In this category, you will find suitable tubing for all current fittings - For standard O.D. tubing, the outside diameter of the tube is specified as the tube size. - All different type of tubing with different material according to specific requirement are available. - FESTO Standard Pneumatic Tubing - FESTO Spiral Tubing - FESTO Pneumatic Piping Systems

Janatics Accessories

Janatics AND Valve (Sizes: M5, G1/8, G1/4)

AND valve delivers air at the outlet (A) only when air signal is present at both inputs (X and Y) - If two signals of different pressure is applied, the lower pressure is connected to outlet (A). -Type: Directional Control Valves (mainly 3/2, 5/2, 5/3) Actuation: Manual, Mechanical, Pneumatic, or Solenoid operated Mounting: Sub-base / Manifold / Individual Sizes: Port sizes available (typically M5, 1/8', 1/4', etc.) Construction: Aluminium / Anodized body for durability Sealing: Nitrile (NBR) seals for long life Operating Pressure Range: ~1.5 to 10 bar Medium: Compressed air, filtered & lubricated / unlubricated Temperature Range: 5°C to 60°C (approx.) The GA Series from Janatics are pneumatic valves widely used in industrial automation for controlling compressed air flow. Used in automation panels, machinery, pick & place systems, packaging, and material handling. Ideal for directional air control in cylinders, actuators, and other pneumatic systems.

Janatics Accessories

Inline Slide Valve (Sizes : R1/8, R1/4, R3/8, R1/2, R3/4)

Inline mounted - Sleeve type, saves space - Smooth, easy operation -Note the direction of flow before installation and connect piping accordingly. Flush pipings for dirt, dust, rust and other foreign particles. Install in clean atmosphere. Use teflon tape on taper threads. Ensure teflon tape does not enter the unit during tightening. Application • These valves can be used at the inlet of pneumatic tools like screwdriver, grinder etc., pneumatic systems and near machineries using pneumatic systems, for quick and convenient connecting - disconnecting of compressed air. Operation • Moving the sleeve towards ' OUT ', connects the air line to the system and moving the sleeve in the opposite direction, will close the inlet port and exhaust the down stream air.

Janatics Accessories

Nipples (WN series Sizes : M5, 1/8, 1/4, 3/8, 1/2, 3/4, 1)

Wide variety of nipples available - Nickel plated brass body - Male (R) taper threads with thread sealant coating, Male parallel threads with sealing washer (M5 only)

Janatics Accessories

Janatics Junction box (WJ series Sizes : M5, 1/8, 1/4, 3/8, 1/2)

Wide range of models available - Aluminium anodized body - Mounting holes provided -WJ series (Sizes : M5, 1/8, 1/4, 3/8, 1/2)

Janatics Accessories

Air Blow Gun

Easy handling - Compact size - Attractive design - Good flow and characteristics -Blowing off chips in machine tools Foundries Assembly lines Service stations Painting (part cleaning) Textile mills Injection moulding machines (cooling of moulds) Pressure die casting machines

Janatics Accessories

Tube Cutter

Janatics Accessories

Self Sealing, Cross Union & Plug Fittings - M5, 1/8, 1/4, 3/8, 1/2, 3/4, 1”

Janatics Accessories

Janatics pu Tubes

Colored polyurethane Tubes WH Series - Sizes: Ø4, 6, 8, 10, 12mm OD (Silver, Transparent, Red, Black, Yellow) Provide differentiation of air line in pneumatic circuits - Nylon Tubes Pneumatic cylinders (all types) Directional control valves, solenoid valves and other valves Air preparation units like filter, regulator and lubricators Pneumatic control panels All compressed air lines, machinery of all kinds wherever pneumatic systems are used Pneumatic circuits in any industry - Polyurethane Coiled Tubes WHC series (Tube sizes: Ø4, 6, 8, 10, 12mm OD) Self retracting & space saving Pneumatic control and power lines Air tools Assembly work stations Service stations / Garage equipments Machine tools

Janatics Accessories

High Pressure Silencer

Series AS02M

Janatics Accessories

Silencer (AS series Sizes : M5, 1/8, 1/4, 3/8, 1/2)

Brass body and sintered bronze silencer elements - Button, Conical, Silencer cum flow control (with lock nut), Silencer cum flow control (with spring) types - Good flow and silencing characteristics - Can be cleaned by kerosene and soap water

Janatics Accessories

Janatics Multi Distributor Fittings- M5, 1/8, 1/4, 3/8, 1/2, 3/4, 1”

Attractive design - Compact size - Threaded nipples of L, T & Y fittings enable plastic portion to turn by 360° - Full area of the inner bore of the tubing is available for flow of fluid - Bubble tight sealing of tubes - Suitable for both Nylon and PU tubing - Easy and quick push-in connection of tube / easy removal of tube by simple pressing of collet cap - 'New design' - Stainless steel collet - Teflon pre-coated male taper threads - Maintenance free and long life - The fitment and function of tubes are not affected by vibrations due to positive gripping of the tube by the collet One-touch fittings can be effectively used in all compressed air applications. Some of the pneumatic applications include Pneumatic cylinders (all types) Directional control valves, solenoid valves and other valves Air preparation units like filter, regulator and lubricators Pneumatic control panels All compressed air lines, machinery of all kinds wherever pneumatic systems are used Pneumatic circuits in any industry

Janatics Accessories

Janatics Swivel Fittings- M5, 1/8, 1/4, 3/8, 1/2, 3/4, 1”

Attractive design - Compact size - Threaded nipples of L, T & Y fittings enable plastic portion to turn by 360° - Full area of the inner bore of the tubing is available for flow of fluid - Bubble tight sealing of tubes - Suitable for both Nylon and PU tubing - Easy and quick push-in connection of tube / easy removal of tube by simple pressing of collet cap - 'New design' - Stainless steel collet - Teflon pre-coated male taper threads - Maintenance free and long life - The fitment and function of tubes are not affected by vibrations due to positive gripping of the tube by the collet - One-touch fittings can be effectively used in all compressed air applications. Some of the pneumatic applications include Pneumatic cylinders (all types) Directional control valves, solenoid valves and other valves Air preparation units like filter, regulator and lubricators Pneumatic control panels All compressed air lines, machinery of all kinds wherever pneumatic systems are used Pneumatic circuits in any industry - While ordering Swivel Fittings, mention the ordering number given in the corresponding table, and for tubes, mention the ordering number with required length in metres.

Janatics Accessories

Janatics Y Type Fittings- M5, 1/8, 1/4, 3/8, 1/2, 3/4, 1”

Attractive design - Compact size - Threaded nipples of L, T & Y fittings enable plastic portion to turn by 360° - Full area of the inner bore of the tubing is available for flow of fluid - Bubble tight sealing of tubes - Suitable for both Nylon and PU tubing - Easy and quick push-in connection of tube / easy removal of tube by simple pressing of collet cap - 'New design' - Stainless steel collet - Teflon pre-coated male taper threads - Maintenance free and long life - The fitment and function of tubes are not affected by vibrations due to positive gripping of the tube by the collet - One-touch fittings can be effectively used in all compressed air applications. Some of the pneumatic applications include Pneumatic cylinders (all types) Directional control valves, solenoid valves and other valves Air preparation units like filter, regulator and lubricators Pneumatic control panels All compressed air lines, machinery of all kinds wherever pneumatic systems are used Pneumatic circuits in any industry - While ordering Type - Y Fittings, mention the ordering number given in the corresponding table, and for tubes, mention the ordering number with required length in metres

Janatics Accessories

Janatics Tee Type Fittings - M5, 1/8, 1/4, 3/8, 1/2, 3/4, 1”

Janatics Accessories

Janatics Straight Fittings - M5, 1/8, 1/4, 3/8, 1/2, 3/4, 1”

Attractive design - Compact size - Threaded nipples of L, T & Y fittings enable plastic portion to turn by 360° - Full area of the inner bore of the tubing is available for flow of fluid - Bubble tight sealing of tubes - Suitable for both Nylon and PU tubing - Easy and quick push-in connection of tube / easy removal of tube by simple pressing of collet cap - 'New design' - Stainless steel collet - Teflon pre-coated male taper threads - Maintenance free and long life - The fitment and function of tubes are not affected by vibrations due to positive gripping of the tube by the collet - One-touch fittings can be effectively used in all compressed air applications. Some of the pneumatic applications include Pneumatic cylinders (all types) Directional control valves, solenoid valves and other valves Air preparation units like filter, regulator and lubricators Pneumatic control panels All compressed air lines, machinery of all kinds wherever pneumatic systems are used Pneumatic circuits in any industry While ordering Straight Fittings, mention the ordering number given in the corresponding table, and for tubes, mention the ordering number with required length in metres.

Janatics Accessories

Janatics Elbow Fittings - M5, 1/8, 1/4, 3/8, 1/2, 3/4, 1”

Attractive design - Compact size - Threaded nipples of L, T & Y fittings enable plastic portion to turn by 360° - Full area of the inner bore of the tubing is available for flow of fluid - Bubble tight sealing of tubes - Suitable for both Nylon and PU tubing - Easy and quick push-in connection of tube / easy removal of tube by simple pressing of collet cap - 'New design' - Stainless steel collet - Teflon pre-coated male taper threads - Maintenance free and long life - The fitment and function of tubes are not affected by vibrations due to positive gripping of the tube by the collet -One-touch fittings can be effectively used in all compressed air applications. Some of the pneumatic applications include Pneumatic cylinders (all types) Directional control valves, solenoid valves and other valves Air preparation units like filter, regulator and lubricators Pneumatic control panels All compressed air lines, machinery of all kinds wherever pneumatic systems are used Pneumatic circuits in any industry -While ordering Elbow Fittings, mention the ordering number given in the corresponding table, and for tubes, mention the ordering number with required length in metres.

Janatics Accessories

Janatics One Touch Fittings (Stainless Steel) - Ø4 & Ø16 mm

Attractive design - Compact size - Threaded nipples of male elbow fittings enable to by 360 degree - Full area of the inner bore of the tubing is available for flow of fluid - Stainless steel design ensures superior clamping by bubble tight sealing of various tubes - Suitable for different materials of tubing (Nylon (Polyamide), Soft Nylon, Polyurethane, Polyethylene) - Easy and quick push-in connection of tube / easy removal of tube by simple pressing of collet cap - Maintenance free and long life - Short parallel threaded connection - Male thread seal - BSP - PTFE seal - No loosing of tube due to vibration - positive gripping by collet - While ordering fittings, mention the ordering number given in the corresponding tables, and tubes mention the ordering number with required length in metres

Janatics Accessories

Janatics One Touch Fittings (Mini) - Ø4 & Ø6 mm

Miniature - Save space - Attractive design - Compact size - Full area of the inner bore of the tubing is available for flow of fluid - Bubble tight sealing of tubes - Suitable for both Nylon and PU tubing - Easy and quick push-in connection of tube / easy removal of tube by simple pressing of collet cap - 'New design' - Stainless steel collet - Teflon pre-coated male taper threads - Maintenance free and long life - The fitment and function of tubes are not affected by vibrations due to positive gripping of the tube by the collet One-touch fittings can be effectively used in all compressed air applications Some of the pneumatic applications include Pneumatic cylinders (all types) Directional control valves, solenoid valves and other valves Air preparation units like filter, regulator and lubricators Pneumatic control panels All compressed air lines, machinery of all kinds wherever pneumatic systems are used Pneumatic circuits in any industry

Janatics Accessories

Air Tank While ordering Air Tank, mention the ordering number given in the corresponding tables. - Angular Line Strainer Can be assembled with F15, FRC15, FS15 & L15 series of products Can be assembled directly in airline Bronze filtering element Serviceable - Clamps for FRL CLAMPS FOR REGULATOR AND FRL UNIT - Flow Meter 2 line LCD display for monitoring flow rate and total value Fast response Analog output for monitoring flow rate - Precision Regulator 1/8 & 1/4 Precise pressure control Characteristics such as flow characteristic, pressure characteristic and repeatability are superior compared with standard regulators Excellent relief flow characteristic is available Suitable for Panel & Modular mountings Diaphragm operated, relieving type (Exhaust) Clamp and pressure gauge can be mounted either in the front or the back Can be assembled with F13, FRC13, FS13 & L13 series of products - Precision Regulator G1/2 Some of the applications of precision regulator, 1. Manufacturers of air gauging equipment, 2. Medical equipments, 3. Leak testing equipment, 4. Polishing machinery, 5. Web tensioning, 6. Measuring machines, 7. Ink or paint, Robotics spraying systems, 8. Tank blanketing and many… - Pressure Indicator Compact size Quick response Panel mountable Noiseless performance - Pressure switch New Suitable for DIN 43650 connector Variants available with Integrated LED for switching status indication Robust design Variants available with Nitrile and Viton series - For Modular construction - Shut Off Valve Connecting thread at both ends Connection - G1/4, G3/8, G1/2 Modular mounting with FRL -Shut Off Valve Lockable GS2 Series (Sizes : G1/4, G3/8, G1/2) Modular mounting with FRL Port thread at both ends Window display to show the valve position • ( i.e.) the valve is in On condition or Off condition - Pressure Gauge - Auto Drain Valve NA1 series - Sizes : G1/4, G3/8, G1/2 Individual unit(Externally mountable) Low operating pressure Compact size Elegant design and finish Long life - Pressure Switch Quick response Easy adjustability of set pressure Hysteresis adjustable - Pressure Sensor - 1 output Digital Pressure Sensor (Series PS - R1/8) 2 Colours display (Red / Green) Set pressure selectable (kPa, psi, kgf/cm2, bar) Both upper and lower limits of pressure can be set independently Panel mountable Direct mountable Both PNP & NPN versions Single output - Pressure Sensor - 2 outputs

Air Preparation Units

Janatics Proportional Pressure Regulator

LED display for monitoring output pressure - Fast response - High flow rate - Output pressure is maintained in the event of power loss - IP65 class protection - Compact and lightweight - Suitable for standalone and modular mounting - Straight and right angle cable options available

Janatics Accessories

Janatics Quick Exhaust Valve (Sizes : M5, G1/8, G1/4, G3/8, G1/2)

Increase the speed of the cylinder - With / without silencer - Connection - M5, G1/8, G1/4, G3/8, G1/2 - Type GQ01 series is with silencer to reduce the exhaust noise - GQ01 SILENCER TYPE GQ0170, GQ0150, GQQ0151, GQ0152, GQ0153 -GQ02 PLUG TYPE GQ0270, GQ0250, GQ0251, GQ0252, GQ0253 ALL MAKE AVAILABLE QUICK EXHAUST VALVE JANATICS, FESTO, TECHNO, SMC, CROX

Janatics Accessories

Janatics Non Return Valve (Sizes : G1/8, G1/4, G3/8, G1/2)

In line mounting - Low cracking and closing pressure - Bubble tight elastomer seat - GV160, GV161, GV162, GV163

Janatics Accessories

OR Valve (Sizes: M5, G1/8, G1/4 )

OR valve delivers air at the outlet (A) always supplied by higher pressure (X or Y) - If two signals of different pressure is applied, the higher pressure is connected to outlet (A) -An OR valve (or shuttle valve) is used to allow a function to be executed from either of 2 different places. An output signal is present whenever at least one of 2 signal inputs is activated. It can be used in safety circuits and logic controls. - While ordering OR Valve, mention the ordering number given in the corresponding tables.

Janatics Accessories

Janatics Pneumatic Preset Counter (Series GC)

Continuously visible preset - Integrated pneumatic reset - 3 or 5 digit display - Convenient button setting

Janatics Accessories

Janatics Flow Control Valve - Metal (Series GR - Size 3/4, Metal type Flow control valve)

Directly mountable on cylinder / valve ports - Fine regulation of air flow - Male threads (G) with sealing washer - Elegant design and finish - Slotted head screw adjusting type

Janatics Accessories

Janatics Pilot operated Non-Return Valve (GV2 series, Sizes : G1/8, G1/4, G3/8, G1/2)

Available in two versions - Low cracking and closing pressure - Bubble tight - elastomer seat - Plastic portion can be turned by 360° - Teflon pre-coated male taper threads

Janatics Accessories

Flow Control Valve (GR2 series Sizes : M5, 1/8, 1/4, 3/8, 1/2)

Directly mountable on cylinder/valve ports - Can be rotated by 360 degree - Fine regulation of air flow - Nickel plated body - Male threads(R) teflon coated - Elegant design and finish

Janatics Accessories

Janatics Pilot operated Non-Return Valve- Metal (GV2 series Sizes : G1/8, G1/4, G3/8, G1/2)

Low cracking and closing pressure - Bubble tight - elastomer seat - Can be turned by 360° - Right metal housing

Janatics Accessories

Janatics Flow control valve - Inline type (GR2 series Sizes : Ø4, 6, 8, 10 & 12mm)

Fine regulation of air flow - Elegant design and finish - Available sizes : Ø4, 6, 8, 10 & 12mm janatics inline flow control valves

Janatics Accessories

Auto Drain Valve (NA1 series - Sizes : G1/4, G3/8, G1/2)

Individual unit(Externally mountable) - Low operating pressure - Compact size - Elegant design and finish - Long life

Janatics Accessories

Janatics Pressure Gauge (FRL series - Sizes : G1/8, G 1/4)

Pressure Gauge (FRL series - Sizes : G1/8, G 1/4) 1/8' = 0-4 bar = A2G01 , 0-10 BAR = A2G02 , 0-16 BAR = A2G03 1/4' = 0-4 BAR = A2G07 , 0-10 BAR = A2G08 , 0-16 BAR = A2G09 ALL JANATICS PRODUCTS AVAILABLE

Janatics Solenoid Valve

Janatics Rotary slide valves

G1/4 Series DR & G1/2 Series DR - Easy handle movement and precise control of the direction - Compact and lightweight design - Handle position available in two types ( Ref. Fig.1 & Fig.2) - Both body mounting and Panel mounting is possible - Good flow characteristics

Janatics Air Cylinders

Compact Cylinders A02 AND A03 SERIES

Compact Cylinder A02 Compact Cylinder with Guide Rod Compact Cylinder with Guide Rod Magnetic Compact Magnetic Cylinder A03 SERIES A02 AND A03 COMPACT CYLINDER A02 NON MAGNETIC CYLINDER A03 MAGNETIC CYLINDER A02 SERIES COMPACT CYLINDER WORKING PRESSURE :- 0.5 TO 10 BAR CYLINDER BORE SIZES :- 12, 16, 20, 25, 32, 40, 50, 63, 80,100 CYLINDER STROKES SIZES:-5MM TO 100 MM TEMPERATURE :- -10 TO 60C Compact, lightweight, and space saving design Large clamping force in relation to their size Low friction (Comparing to other series) Elastomer end cushion A03 COMPACT CYLINDER MAGNETIC COMPACT CYLINDERS MAGNETIC Double Acting ( Ø12 - 100 ) mm Compact, lightweight, and space saving design Large clamping force in relation to their size Low friction (Comparing to other series) Elastomer end cushion CYLINDER BORE SIZES :- 12, 16, 20, 25, 32, 40, 50, 63, 80, 100 CYLINDER STROKES SIZES :- 5MM TO 100MM WORKING PRESSURE :- 0.5 TO 10 BAR A03 MAGNETIC CYLINDER MAGNETIC REED SWITCH A12, A16, A20, A25 BORE REED SWITCH AM2012 A32, A40, A50, A63, A80, A100 REED SWITCH AM2032 CYLINDER :- FEMALE , MALE THREDAD

Janatics Air Cylinders

JANATICS PROFILE (Square ) CYLINDER A23 AND A24 SERIES

Non Rotating Rod Cylinder A23H, A24H - Standard Cylinder A23, A24 - Double End Cylinder A20, A21 - Tandem Cylinder A23T, A24T -A23H AND A24H SERIES The A23H / A24H series are double-acting square-profile cylinders manufactured per VDMA 24562 / ISO 15552 standards, with bore sizes from Ø32 mm to Ø63 mm They feature a hexagonal piston rod that inherently prevents rotation, crucial for alignment-sensitive mechanisms Available in magnetic (A24H) and non-magnetic (A23H) versions, with a standard magnetic sensor design compatible across all sizes Fresh Catalog Mounting options: Extensive choices including foot, flange, clevis, trunnion, etc., aligned with ISO 15552/VDMA 24562 standards Stroke lengths: Standard options from 25 mm up to 500 mm depending on bore size, with cushioning strokes ranging ~21–28 mm depending on configuration Operating pressure: Designed for 0.5–10 bar, with filtered and lubricated compressed air as the media - A23 AND A24 PROFILE NONMAGNETIC AND MAGNETIC CYLINDER The A23 (non-magnetic) and A24 (magnetic) models are double-acting square‑profile pneumatic cylinders, suitable for applications requiring precision, durability, and integrated sensor capabilities They span bore sizes from Ø 32 mm up to Ø 100 mm (and in some documentation up to 125 mm Magnetic piston (A24) allows for easy use of PNP/NPN sensors without needing external magnets; A23 is the non-magnetic variant Feature Specification Series A23 (non-magnetic) / A24 (magnetic) Bore Range :- Ø 32, 40, 50, 63, 80, 100 (125 mm also mentioned in some sources) Stroke Options :- Standard strokes: 25–500 mm; cushioning strokes: ~21–28 mm depending on bore Operating Pressure :- 0.5–10 bar Temperature Range :- Ambient: –10 °C to +60 °C; Media: +5 °C to +50 °C; Optional high‑temp to +150 °C with Viton seals Construction Materials :- Aluminium barrel; optional stainless‑steel piston rod and lock nut (SS 304) DOUBLE END CYLINDER A20 AND A21 SERIES Double End Double Acting Cylinders (Square type) Ø32 - 125 mm Adjustable cushioning at both ends with elastomer pads Wide varieties of mountings as per ISO 15552 / VDMA 24562 standards Magnetic and Non magnetic version Aluminium profile (square) cylinder barrel Magnetic sensor common for all sizes ( Refer Magnetic sensor catalogue ) Optional - High temperature (Viton seals) 150°C max.** Optional - Non corrosive Stainless steel piston rod and piston rod lock nut (SS 304)** JANATICS TANDAM CYLINDER A23T AND A24T SERIES Tandem Cylinders - ( Series A23T, A24T - Ø32 to 125 mm ) Adjustable cushioning at both ends Wide varieties of mountings as per ISO 15552 / VDMA 24562 standards Magnetic and Non magnetic version Aluminium profile (square) cylinder barrel Magnetic sensor common for all sizes (Refer Magnetic sensor catalogue) Piston rod - Non rusting (SS 303 material on request)**

Janatics Air Cylinders

JANATICS A27 AND A28 TIE ROD CYLINDER

Standard Cylinder A27,A28 - A27 MAGNETIC AIR CYLINDER -A28 NON MAGNETIC AIR CYLINDER -TIE ROD STANDARD CYLINDER -AIR CYLINDERS Double Acting - Ø32 - 100 mm -As per ISO 15552 / VDMA 24562 standards -Adjustable cushioning at both ends with elastomer pads -Wide varieties of mountings -Magnetic and Non magnetic version -Optional - High temperature (Viton seals) 150°C max.** -Optional - Non corrosive Stainless steel piston rod and piston rod lock nut (SS 304)*- CYLINDER BORE SIZES :- 32 , 40 , 50, 63, 80, 100 MM CYLINDER STROKES SIZES :- 25MM TO 500 MM The Janatics A27 and A28 series are standard pneumatic cylinders designed for industrial applications, adhering to ISO 15552 and VDMA 24562 standards. Here’s a concise overview based on available information Type: A27: Magnetic (equipped for piston position detection) .A28: Non-magnetic (no magnetic position detection).Design: Double-acting cylinders, meaning they use compressed air for both extension and retraction, ensuring precise motion control. Bore Sizes: Available in 32 mm, 40 mm, 50 mm, 63 mm, 80 mm, 100 mm, and 125 mm Stroke Lengths: Range from 25 mm to 1000 mm (e.g., A27080025O for 80 mm bore with 25 mm stroke, A270801000O for 1000 mm stroke).

Janatics Air Cylinders

JANATICS A12 AND A13 SERIES ISO 6431 (Tie rod)

JANATICS AIR CYLINDER SINGLE ACTING CYLINDER A12 AND A13 SERIES A12 NON MAGNETIC CYLINDER A13 MAGNETIC CYLINDER ISO 6431 STANDARD CYLINDER - Standard Cylinder A12, A13 - Double End Cylinder A10, A11 As per ISO 6431 / CETOP RP43P, RP53P standards Adjustable cushioning at both ends Wide varieties of mountings Low friction Long life SINGLE ACTING CYLINDER TIE ROD A12 AND A13 SERIES CYLINDER BORE SIZES :- 32 , 40 ,50 ,63 ,80 AND 100 STOCKES :- 25MM TO 500 MM WORKING PRESSIRE ;- 2 TO 10 BAR TEMPERATURE -10 TO 60 C MATERIALS OF CONSTRUCTION :- ALUMINIUM , BRASS , NITRILE , STEEL , ACETAL ACCESSORIES :- MALE CLEVIS , FEMALE CLEVIS , CLEVIS FOOT BRACKET , WALL MOUNTING , TRUNNION BRACKET , ROD AND FROK , ROD AND ALIGNER , ROD AND EYE ,

Air Preparation Units

Janatics FRCL Modular

Filter Regulator Combination Lubricator with Modular - FRCLM without Piping Adopter - Sizes: G1/4, G3/8, G1/2, G3/4, G1 -FRCLM with Internal Auto drain -Modular type for easy and fast maintenance Suitable for wall mounting Filter • Bronze filtering element • Separator and shield for efficient moisture separation Internal Autodrain • Float type, no electrical connections required • Manual drain is also provided / possible • Provision for drain tube connection, to take the condensate away from the unit, to keep the working area clean Regulator • Diaphragm operated, relieving type • Pressure compensated by balanced poppet • Flow compensated (with venturi) for faster response • Non raising Press to lock adjusting knob for locking at any set pressure Lubricator • Fog / Mist type Lubricator • Fine adjustment of lubrication • Lubrication proportional to flow Steel bowl guard, bayonet type on FRLM14, FRLM15 & FRLM17 models Good flow and regulating characteristics - FRCLM without piping adaptor Modular type for easy and fast maintenance Suitable for wall mounting Filter • Bronze filtering element • Separator and shield for efficient moisture separation • Press type manual drain for easy operation Regulator • Diaphragm operated, relieving type • Pressure compensated by Balanced poppet • Flow compensated in models FRCLM14, FRCLM15 and FRCLM17 for faster response • Non raising Press to Lock adjusting knob for locking at any set pressure Lubricator • Fog/Mist type Lubricator • Fine adjustment of lubrication • Lubrication proportional to flow Steel bowl guard, bayonet type on FRCLM14, FRCLM15 and FRCLM17 models and threaded type on FRLM13 model Good flow and regulating characteristics

Air Preparation Units

FRL Modular

Filter, Regulator, Lubricator with Modular - FRLM without Piping Adopter - Sizes: G1/4, G3/8, G1/2, G3/4, G1

Air Preparation Units

Janatics Filter Regulator Combination

Janatics air filter regulator - Sizes: G1/4, G3/8, G1/2, G3/4, G1 - FRC with Manual Drain Modular type Suitable for panel mounting Filter • Bronze filtering element • Separator and shield for efficient moisture separation Regulator • Diaphragm operated, relieving type • Pressure compensated by balanced poppet • Flow compensated in models FRC14, FRC15 and FRC17 for faster response • Non raising press to lock adjusting knob for locking at any set pressure Steel bowl guard, bayonet type on FRC14, FRC15 & FRC17 models and threaded type on FRC13 model Good flow and regulating characteristics - FRC with Internal Autodrain Modular type Suitable for panel mounting Filter • Bronze filtering element • Separator and shield for efficient moisture separation • Bayonet type steel bowl guard Internal auto drain • Float type, no electrical connections required • Provided with manual drain • Provision for drain tube connection, to take the condensate away from the unit, to keep the working area clean Regulator • Diaphragm operated, relieving type • Pressure compensated by balanced poppet • Flow compensated for faster response • Non raising Press to lock adjusting knob for locking at any set pressure Good flow and regulating characteristics - FRC with Metal bowl Modular type Suitable for panel mounting Filter Bronze filtering element Separator and shield for efficient moisture separation Press type manual drain for easy operation Suitable for automatic drain Regulator Diaphragm operated, relieving type Pressure compensated by balanced poppet Flow compensated Non raising Press to lock adjusting knob Aluminium bowl guard, bayonet type (3/4 and 1' only) Good flow and regulating characteristics

Air Preparation Units

Janatics Regulator

Sizes: G1/4, G3/8, G1/2, G3/4, G1 - Regulator Conform to ISO 6953 - 1 Suitable for panel and modular mountings Non raising Press to Lock adjusting knob for locking at any set pressure Diaphragm operated, relieving type Pressure compensated by balanced poppet Flow compensated in models R14, R15 and R17 (with venturi) for faster response Good flow and regulating characteristics - Regulator with NRV Conform to ISO 6953 - 1 Suitable for panel and modular mountings Non raising Press to Lock adjusting knob for locking at any set pressure Diaphragm operated, relieving type Pressure compensated by balanced poppet Flow compensated in models R14 and R15 (with venturi) for faster response Good flow and regulating characteristics Built in non return valve allows free air flow in reverse direction. When the inlet air is reduced by and below the setup pressure

Janatics Air Cylinders

JANATICS COMPACT ISO CYLINDER

Compact ISO Cylinder A63, A64 - Double End Cylinder A60, A61 - Multi Position Cylinder A63, A64

janatics

Subcategory Tags

Contact Us